casio qt 6100 user manual

casio qt 6100 user manual

Wind the AC adaptor cable around the ferrite core two times. The ferrite core is packed with QT-6100. Init Sw INIT Copyright(C) 2004 CASIO COMPUTER CO.,LTD. All rights reserved. ROM VER. xxxxxx xxxx CREATE. CARD SLOT COVER Screws 9. Release the hook and remove the REAR CASE. 10. Remove four screws and the iron plate. 11. Remove 14 screws and then the LCD unit.Terminal side 6. Fix the iron plate with twelve screws.Connect four connectors and one FPC.Fix the backup battery cover with one screw. Connect the DRAWER wiring (a cable and an earth). CARD SLOT COVER Screws 13. Be careful with the position of the screw holes. 6. Fix the cap to the stand. Be careful with the direction of the cap. The height of the screw hole on the front side should be lower. 7. NOTE: The lead wires should be stored neatly in a line. 5. Fix the metal bracket to QT-6100 with two screws. 6. Connect the connector to QT-6100. NOTE: Arrange the cables so that they do not tangle with each other. INIT Copyright(C)2004 CASIO COMPUTER CO.,LTD. All rights reserved. ROM VER xxxxxx xxxx CREATE. XXXXXX: additional action n: number of times a: action g: group d: device number 7-4. Status Display With the EX820, the following display is displayed on the LCD (SVGA). Operation: The following tests are performed automatically. Perform the CF-CARD clear test, before start of this test.In case of one time check only, the test can be ended by the judgment (OK or NG) of the opera- tor. The display can be switched by the touch of the panel. The display will not change to the next one unless the panel is touched. Make sure to connect REMOTE DISP to COM3. In case of one time check only, the test can be ended by the judgment (OK or NG) of the opera- tor. The loop back test is performed from COM1 to COM 3 by the following setting by one time check. When changing the ID, turn the power on again.The test enters the wait mode for only MCR input.http://www.rencontres-icare.org/userfiles/harbor-freight-manual-tire-changer-part-2.xml

• casio qt 6100 user manual, casio qt 6100 service manual, casio qt 6100 user manual, casio qt 6100 user manual pdf, casio qt 6100 user manual download, casio qt 6100 user manual instructions, casio qt 6100 user manual free.

A bus transaction consists of an address cycle followed by one or more data cycles. PCI Bus Command and Byte Enables.The video memory row and column addresses are multiplexed on these lines.The following table lists the error messages and describes the action to take. This sheet holder is prohibited by pro- Set correct sheet holder. gram. E141 Press key is not pressed twice Follow the prompt message.CF card is not inserted to the slot. Insert CF card. E201 Format error. CF card data or formats illegal.Meaning Prompt message Data cannot be printed out.These error codes are displayed or printed on error log report.Therefore, the OS displays a message as shown below and stops the operation of ECR. Such errors include errors of the OS (ITRON) itself, driver system errors, etc. The values of Error No. This phenomenon may occur when the exclusion function of ITRON is used. Possible causes: A software bug or an illegal operation of ITRON. (2) Mailbox creation error Error No. However, an illegal address may be displayed depending on the exception code.Possible causes: It is hard to think that this phenomenon is caused by software, because these errors occur due to an internal operation of the CPU. M51957BFP (IC33) POWER POWER INPUT 25uA OUTPUT INPUT OUTPUT DELAY VALUE 1.25V DELAY VALUE 14. RTC-7301DG (IC19) Control Line 32.768 kHz Digital Trimming FOUT DIVIDER REGISTER Temperature. Simplified operation is made possible by a specially designed touch screen and a wide selection of automated, programmable functions. A specially designed keyboard layout and a bright, easy-to-read color display help to take the fatigue out of long hours operation. In the operation e xamples contained in this manual, the print and display samples ar e not actual size. Also, all samples ar e just images. Manufacturer: CASIO COMPUTER CO., LTD.http://cinstech-inspect-survey.com/fckeditor_userfiles/harbor-freight-manual-winch.xml

6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Representative within the European Union: CASIO EUROPE GmbH Bornbarch 10, 22848 Norderstedt Germany WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Please k eep all inf or mation f or future ref erence. GUIDELINES LAID DO WN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (Not applicable to other areas) W ARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC W ARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user ’ s authority to operate the equipment. Apparaten skall anslutas till jordat natuttag. NL Batterij niet This product Contains Mercury and must be recycled or Deposed of Properly.Please ensure that the socket outlet is installed near the equipment and shall be easily accessible. About the icons In this guide various icons are used to highlight safe operation of this product and to prevent injury to the operator and other personnel and also to prevent damage to property and this product. The icons and definitions are given below. Indicates that there is a risk of severe injury or death if used incorrectly. Indicates that injury or damage may result if used incorrectly.http://izpunpeni.eklablog.com/gfci-type-manual-transfer-switch-a203826850

Icon examples T o bring attention to risks and possible damage, the following types of icons are used. The symbol indicates that it includes some symbol for attracting attention (including warning). In this triangle the actual type of precautions to be taken (electric shock, in this case) is indicated. The symbol indicates a prohibited action. In this symbol the actual type of prohibited actions (disassembly, in this case) will be indicated. The symbol indicates a restriction. In this symbol the type of actual restriction (removal of the power plug from an outlet, in this case) is indicated. W arning! Handling the terminal Should the terminal malfunction, star t to emit smoke or a strange odor, or otherwise behave abnormall y, immediately shut do wn the power and unplug the A C plug from the po wer outlet. Do not place containers of liquids near the terminal and do not allo w any f oreign matter to get into it. Should water or other f oreign matter get into the terminal, immediately shut down the po wer and unplug the A C plug from the power outlet. Should y ou dr op the terminal and damage it, immediately shut down the po wer and unplug the A C plug from the po wer outlet. Contact CASIO service representative. Use of an outlet with a different v oltage from the rating creates the danger of malfunction, fire, and electric shoc k. Overloading an electric outlet creates the dang er of o verheating and fire. Please use the adaptor in the carton bo x for this terminal. Use another adaptor ma y cause fire, electrical shock, or malfunction. Make sure the power plug is inserted as far as it will go. Never connect to a power outlet that is loose. Use a dry cloth to periodicall y wipe off an y dust b uilt up on the pr ongs of the plug. Humidity can cause poor insulation and create the danger of electric shoc k and fire if dust sta ys on the prongs. Do not allow the po wer cor d or plug to become damaged, and never try to modify them in any wa y. Caution!http://fodocoburg.eklablog.com/gfd-private-pilot-manual-download-a203826852

Do not place the terminal on an unstable or une ven surface. The abo ve conditions can cause malfunction, which creates the danger of fire. Do not overlay bend the power cord, do not allow it to be caught between desks or other furniture, and never place heavy objects on top of the power cord. Doing so can cause shorting or breaking of the power cord, creating the danger of fire and electric shock. Be sure to grasp the plug when unplug ging the power cor d fr om the wall outlet. Pulling on the cor d can damage it, break the wiring, or cause short, creating the danger of fire and electric shock. Never touc h the plug while y our hands are wet. Doing so creates the danger of electric shoc k. Pulling on the cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock. Never touc h the printer head and the platen. Important! Do not tilt without loosing the screws. Even in these cases, you can open the cash drawer by pulling drawer release lever (see below). Important! The drawer will not open, if it is locked with a drawer lock key.Drawer (option) The drawer opens automatically whenever you finalize a registration and you issue a read or reset report. Drawer loc k (for medium size drawer) Use the drawer key to lock and unlock the drawer. Drawer open ke y (f or large size drawer) Use the drawer open key to open the drawer.Such objects can damage the screen. Use this key to show the programmed function key list. Use this key to register the function key which is not located on the keyboard but assigned in the memory. F Separate check key. Use this key in a check tracking system to separate selected items from one check to another check. If this key is registered, a pop-up window for separating a check is opened. G Finalization list key. Use this key to show the programmed finalization key list. Use this key to register the finalization key which is not located on the keyboard but assigned in the memory.

H Post r eceipt key; Use this key to produce a post-finalization receipt. I Page up key g Use this key to turn the window forwards. J Home position key z Use this key to return the cursor to the home position. K Page down key w Use this key to turn the window backwards. N New balance key S Use this key to add the current registered total amount to the previous balance to obtain a new balance. When this key is pressed, the total amount of the transaction is calculated. Normally, a receipt is issued. When the clerk inputs a check number, the register checks to see if that number already exists in the check tracking memory. If there is no matching number in the memory, a new check is opened under the input number. If the check number matches a number already stored in the memory, that check is reopened for further registration or finalization.Consult your CASIO dealer for detail information. Add check Use this key in a check tracking system to combine the details of more than one check into a single check. Arrangement Use this key to activate an arrangement program pro- grammed in the arrangement file. Any operation that can be performed from the keyboard, as well as mode, can be programmed in an arrangement program, and can be performed merely by pressing this key. In addition, one numeric entry can be included in an arrangement pro- gram. In this case, input the number and press this key. The mode control function of this key can be pro- grammed for all modes except for the OFF mode. Bill copy Use this key to issue bill copy. Charge Use this key to register a charge sale. Check Use this key to register a check tender. Check endorsement Use this key to print a preset check endorsement message using the slip printer. Check print Use this key to print the check on the slip printer. Clerk number Use this key to assign a clerk ’ s secret number. Clerk transfer Use this key to transfer opened checks to another clerk. Coupon Use this key for registering coupons.

Coupon number Use this key for registering mix and match discount by entering coupon number. Coupon 2 Use this key to declare the next item registration as coupon. Cr edit Use this key to register a credit sale. Cube This key provides the same functions as the Square key. In addition, this key also has a cube multiplication function. Currency exchange Use this key to convert foreign currency to local currency or vice versa using the exchange rate preset for the key and displays the result. Use this key for conversions of a home currency subtotal or merchandise subtotal to equivalent of another country's currency. Use this key for conversions of another country's cur- rency to the equivalent of the home currency. Customer ID number Use this key to enter customer ID number. Declaration Use this key to declare in drawer amount for money declaration. Department Use this key to register department. Department number Use this key to enter department number. Deposit Use this key to register deposits. Discount Use this key to register discounts. Display mode Use this key to choose item consolidation display format or non-item consolidation display format. Dutch account Use this key to share the total payment by customers. Eat-in Use this key to specify if the customer eats in the restau- rant. Before closing a transaction press this key. EBT (electronic benef it transfer) Use this key to register an EBT amount with a tender amount input. Electronic jour nal display Use this key to display the stored journal. This key is also used for specifying sub currency while entering an amount of payment. Paid out key: Use this key following a numeric entry to register money paid out from the drawer. 1st unit price Use this key to register a specific item at the first unit price. F ood stamp shift Use this key to change food stamp status. F ood stamp subtotal Use this key to obtain the food stamp applicable amount.

F ood stamp tender Use this key to register a food stamp payment amount with a tender amount input. House Bon Use this key to register items for in-store use. Item search Use this key to search an item by its name. List number Use this key to enter list number. Loan Use this key to input the amount of money provided making change. K etten Bon Use this key to enter quantities for multiplication. Multiplication by this key issues singular order prints. Media change Use this key to change media in drawer amounts. Merchandise subtotal Use this key to obtain subtotal excluding the add-on tax amount and the previous balance. Minus Use this key register subtraction. New check Use this key in a check tracking system to input a new check number in order to open a new check under that number. No sale Use this key to open the drawer between transaction. Non-add Use this key to print reference numbers (personal check number, card number, etc.) Normal r eceipt Use this key to change the order status from Bon to normal. OBR (Optical bar code reader) Use this key to input optical barcodes manually. Old check Use this key in a check tracking system to input the number of an existing check (previously created by the New check key) whose details are stored in the check tracking memory. Existing checks are reopened to perform further registration or to finalize them. Open Use this key to temporary release a limitation on the number of digits that can be input for a unit price. Open 2 Use this key to suspend the compulsory specifications. Open check Use this key to issue an open check report of an assigned clerk. Operator number Use this key to enter a clerk number during clerk trans- fer. Order character change Use this key to change the order character. The order characters not only of the item but in the order character table can be printed. Payment Use this key to declare the following transactions as payment. PLU number Use this key to enter PLU number.

Plus Use this key for registering surcharge. Pick up Use this key to pick up media in drawer. Premium Use this key to apply a preset % or manual input % to obtain the premium amount for the last registered item or subtotal. Price Use this key to register an open PLU. Price inquiry Use this key to confirm the price and descriptors of PLU without registering. Post entry Use this key to indicate the reserved item of set menu and register it as a fixed item later on. Post r eceipt Use this key to produce a post-finalization receipt. In addition, this key also has a split price function. Recall Use this key for recalling the transferred check number by the store key. When this key is pressed, the check number will appear in order of the oldest record. This key should be pressed twice. Received on account Use this key following a numeric entry to register money received for non-sale transaction. Refund Use this key to input refund amounts and void certain entries. Round repeat Use this key to register the same items which were ordered just before. Seat number Use this key to enter and print seat number. 2nd unit price Use this key to register a specific item at the second unit price. Separate check Use this key in a check tracking system to separate selected items from one check to another check.This key is also used to release the slip paper holder if num- bers are not entered. This is done by specifying the number of feed lines. This key is also used to release the slip paper holder if numbers are not entered. Slip print Use this key to execute a slip batch printing on the slip printer. Pressing this key prints the sales details. Actual printing is performed following receipt issuance. Square This key provides the same functions as the Multiplica- tion key. In addition, this key also has a square multipli- cation function. Stock inquiry Use this key to check the current stock quantity for a PLU without registering.

Store Use this key for storing the check number of the regis- tered items. When this key is pressed, registered item data will be stored, and then these data will transfer to the youngest check number. Subdepartment Use this key to register items for the subdepartment. Subdepartment number Use this key to enter subdepartment number. Substitution Use this key to replace group PLU with a PLU which is not preset in the pulldown menu. T able number Use this key to input table numbers. T able sharing Use this key to assign one table to two or more customer groups. T akeout Use this key to specify if the customer takes out items, before total a transaction. Press this key for the tax exemption. T ax exempt Use this key to change taxable amounts to nontaxable amounts. T ax shift Use this key to activate the tax table which is specified by the same tax status programmed for this key. T axable amount subtotal Use this key to obtain taxable amount subtotal. T ext print Use this key to enter characters to print. T ext recall Use this key to print preset characters. Tip Use this key to register tips. T ray total Use this key to display the total amount for all registra- tions from the last registration until this key is pressed or registrations between presses of this key. V alidation Use this key to validate item or transaction amounts on the slip. VA T Use this key to print VAT breakdowns. Ke ys in c heck No. pop-up window Special function keys to control check No.Next (Page up) Use this key to turn the pop-up window forwards. Pr evious (Page do wn) Use this key to turn the pop-up window backwards. Escape Use this key to terminate the operation of the pop-up window and close it.The method you of assigning clerk depends on the programming of the terminal. Clerk number ke y The o key is used for the clerk secret number key.All available modes of the clerk are displayed. C REG C 01 000123 31-10-04 12:34. 0.

00 Adjusting the time and date Y ou can adjust the time or date in the PGM 1 mode. Press key and press icon.The input value takes priority of the preset value. Registering discounts The following example shows how you can use the p key in various types of registration.Registering reductions The following examples show how you can use the m key in various types of registration.Case A OPERATION DISPLAY 600 ( ?P 15- a PRINTOUT (by optional remote printer) Mode REG 1 Press the P key, which converts the subtotal amount into the sub currency by applying the preset exchange rate. And the subtotal in the sub currency is shown on the display. 1 Press the a key to finalize the transaction. The change amount is shown in the pro- grammed currency.And the subtotal in the sub currency is shown on the display. 1 Press the a key to finalize the transaction. The change amount is shown in the pro- grammed currency.Press R before the item you want to return.This registration must be performed out of a sale. PRINT OUT OPERA TION (by optional remote printer) ? 7-- r Amount can be up to 8 digits. Registering mone y paid out The following example shows how to register money paid out from the terminal. This registration must be performed out of a sale. PRINT OUT OPERA TION (by optional remote printer) ? 150 P Amount can be up to 8 digits.P ost-finalization receipt The post-finalization receipt lets you issue a receipt after finalization of the transaction. Receipt is not issued.Example 3 Y ou can use the following operation to add customers to an original number of customers input (when addition to the number of the customer is allowed).In this procedure, “ Allow clerk to open check No.For example, if clerk 1 is interrupted while registering a transaction, clerk 2 can use the same machine to register a different transaction. Then clerk 1 can continue the original registration from the point where it was interrupted.

When clerk 1 signs back on (after being interrupt by clerk 2), the cancel operation cancels only the items registered after signing back on (only this receipt) or from the top of the transaction.The capacity of the registration buf fer memory is determined by the number of records of registration buffer memory reserved by the memory allocation operation. There are two ways to print slips: 1. Print all items that are registered until the last slip printing. 2. Print only additional items that are registered until the last receipt issuance (ex.If you select “ option 2 ”, program “ Auto Line Find ” also. Y ou can print slips using automatic or manual batch printing. Finalizing a registration without inserting a slip paper into the slip printer when the terminal is programmed as “ Slip Automatic Batch Print Compulsory ” produces an error. T o perform auto batc h printing 1 Insert a slip paper into the slip printer.The check is cleared after printing finalized data on slip or guest check receipt, or check is also cleared when the same finalized check number is assigned in new check operation. Printing examples are described under “ Print Additional item only ” programming. T o perform auto batc h printing 2 Insert a slip paper into the slip printer. Once you do, any attempt to exceed the preset maximum results in an error.Example: The check n umber exists in the window Just press the icon instead of entering the check number, and continue the registration. PRINT OUT OPERA TION (by optional remote printer) Press the chec k 3456 icon. 10- ( 20- ) S Example: The check n umber does not exist in the windo w If there is no appropriate check number in the window, enter the appropriate check number and press the key. In this operation, the key is treated as key.Separate check window is opened. Item 1 and 3 are moved from the original check to separated check. Example T o change the clerk for check number 1234 from clerk 1 to clerk 4.

PRINT OUT OPERA TION (by optional remote printer) o 1 B 4 B 1234 B B T able transfer W ith this operation, you can change the number of a check. Example 1 T o change the check number 1234 to 11 1 1 (which is newly opened). NEW CHECK Press this key if you do not want the clerk No.Input the clerk No. of the clerk who is currently in charge of check No. 1234 (tar get check). Input the clerk No. of the clerk who will take over check No. 1234 (target check). Input the target check No.The recalled text is printed on the receipt and journal. Y ou can also choose recall texts by text recall sub window, which is shown by pressing directly.Example OPERA TION DISPLA Y 10. See page 18 of this manual. The terminal checks actual stock quantities against the programmed minimum stock quantities. Stock operations are performed only for PLUs programmed with minimum stock quantities. Stock warnings When the minimum stock value of an item is set, the terminal subtracts its stock quantity from the registered quantity (or registered quantity. The terminal sounds buzzer when the actual stock quantity is less than the minimum stock quantity. Example T o inquire the actual stock quantity of flat-PLU 001. OPERA TION DISPLA Y B ( REG C 01 31-10-04 03:30 PM 001580 PLU001 10.05 — Actual stock quantity STOCK INQ Single item cash sales A department key, subdepartment or PLU programmed with single item sale status finalizes the transaction as soon as it is registered. The single item sales function cannot work properly if the keyboard does not include (the cash key). The single item sales function can only be used for cash sales. Because another item is registered before the single item sales. When an amount is programmed to, attempting to manually input an amount results in an error.Before using the currency exchange function, it is necessary to program the conversion rate and foreign currency amount symbol. Other finalize keys cannot be used.

OPERATION DISPLAY 5 Enter the unit price and press the applicable flat-PLU key. 5 Enter the next unit price and press the applicable flat-PLU key. 5 Press E and s without en- tering a numeric value. This op- eration converts the subtotal (in- cluding tax) dollar value into yen by applying a pre-programmed ex- change rate. This operation converts the entered yen amount into dollars by applying a pre- programmed exchange rate. The result is shown on the display. 5 Press to finalize the transaction. Note that you do not need to reen- ter the dollar amount.OPERATION DISPLAY 5 Enter the unit price and press the applicable flat-PLU key. 5 Enter the next unit price and press the applicable flat-PLU key. 5 Press E and s without en- tering a numeric value. This operation converts the en- tered yen amount into dollars by applying a pre-programmed ex- change rate. The result is shown on the display. 5 Press a to specify cash tender for the yen partial tender. Note that you do not need to reenter the dollar amount.The unit prices appear on the display of the terminal when recalled. Example T o check the unit price of flat-PLU 001. OPERA TION DISPLA Y B ( Scanning PLU Product barcodes are read by scanning with hand-held scanner, and are filed in the scanning PLU link file. The unit price, item descriptor, programming status, link department, totalizer and counter, the terminal are filed in the PLU link file. When a barcode is entered by scanning, or from the keyboard by using (OBR key), the terminal searches its scanning PLU link file and finds the preset unit price to accumulate to the PLU file.This key is used to correct already entered characters. 8 Right cursor key Press this key to shift the character setting position to the right one by one. This key is used to correct already entered characters. SHIFT1-case SHIFT2-case This key is also used for editing the programmed characters. 0 Backspace key Press this key to move the character placed behind.B 1 Press (insert) key.

“ p ” 1 Enter “ p ”. OPERA TION DISPLA Y Designate the item.B 1 Press (delete) key. OPERA TION DISPLA Y Designate the item.B 1 Press (backspace) key.Otherwise, you will not be able to distinguish between the sales data for different dates.The terminal will automatically compare the input with the cash in drawer in the memory and print the differ - ence between these two amounts. Note that if money declaration is required by programming, you cannot skip this procedure. Note that if money declaration is required by programming, you cannot skip this procedure. When an err or occurs Errors are indicated by an error codes. When this happens, you can usually find out what the problem is as illustrated below. Press C and check the appropriate section of this manual for the operation you want to perform. T roubleshooting Prompt message Meaning Action Operator mistake. E001 Wrong mode. E003 Wrong operator. E005 Insufficient memory. E011 Close the drawer. E012 Journal paper end. E014 Receipt paper end. E016 Change back to REG mode. E018 Enter Table number. E019 Enter Number of covers. E020 Enter Seat number. E023 Stock running short. E024 No stock is available. E029 No registration is possible while you are in the tender operation. E031 Press ST key before Finalization. E033 Enter tendered amount. E035 Change amount exceeds the limit. E036 Remove money from the drawer. E037 Digit or Amount Limitation Over. E038 Perform Money Declaration E040 Issue Guest Receipt. E041 Print Validation. E044 Print Cheque. E045 Print Check-Endorsement. E046 REG Buffer Full. Please Finalize or NB. E047 Print bill. E048 Insert Slip Paper and retry. E049 CHECK memory full. E050 Detail memory full. E057 No item exists in detail. E058 Enter post entry item. Error when actual stock value for a registration items is a negative value. Scanning PLU is not found or OBR code is mismatched. Attempted registration whilst partial tender operation is being done.