| File Name: | dolphin battery charger manual.pdf |
| Size: | 3813 KB |
| Type: | PDF, ePub, eBook, fb2, mobi, txt, doc, rtf, djvu |
| Category: | Book |
| Uploaded | 5 May 2019, 13:19 PM |
| Interface | English |
| Rating | 4.6/5 from 827 votes |
| Status | AVAILABLE |
| Last checked | 3 Minutes ago! |
On DOLPHIN PRO charger a specific winterizing charging program is available in order to keep-up the battery. Higher voltage AC travels better over long distances, where the DC does not. Due to this situation, the charger should be mounted as close to the battery as possible. Next on the priority list for consideration is the charger size. Your maximum charger amperage should be 20% of your battery bank size (in amp-hours). This means that you can install two 40-amp chargers to get 80 amps of charge. The most effective way is to have the chargers synchronize (or stack) with each other so the charge algorithm works efficiently. Next you must consider the future of the system. Since an inverter and a charger share many of the same components, installing a combination unit in your system allows cost savings realized from duplicating redundant components. When using separate units, one will always be idle while the other is in use. So for hardware weight and size efficiencies, a combination unit is recommended. However, the battery’s reactions to voltage differential changes with different temperature levels. When a battery is warmer, it has an easier time accepting current, but when it’s colder, it has a higher resistance to current. So, more complex chargers utilize a battery temperature sensor to determine the ability of the battery to accept a charge and will adjust the voltage (higher voltage when cold, lower voltage when warm) to give an optimum charge, and to regulate the temperature of the charging battery. The voltage difference is minimal (typically.03 volt for every degree variance from moderate temperature), but makes a difference in the battery’s longevity. However, a charger that large would cause so much heat build-up in the battery that it would be completely destroyed before too long. On the other side of the spectrum, a 5-amp charger would not damage the battery, but would take over three days to charge.Why?http://www.centrum.elblag.pl/centrum/upload_img/file/california-criminal-history-inquiry-manual.xml
If the charger is determined first, it may limit your battery choices. On the other hand, there are so many charger types that you can always find one (or stackable charger units) to match your battery bank. First consideration is the size, next is battery chemistry. If you decide on a gel battery or an AGM, ensure your charger has the algorithm to match the battery type, and the temperature compensation to effectively charge the bank. Another consideration is input voltage. If you plan on using the charger in a worldwide environment, ensure you select a charger that can operate on a worldwide voltage range. A US-only charger (120V 60Hz input) would certainly be damaged by plugging into European (230V 50Hz) power. However, DOLPHIN Charger can take a wide window of input voltages and still function as designed. How important is it?When warm, charging voltage must be reduced to prevent overcharging and consequent loss of electrolyte. When the battery is located in a well-controlled environment temperature compensation adds little value. In contrast, temperature compensation is absolutely essential when batteries are located in outdoor cabinets or other areas subject to extremes of temperature. These facts illustrate the value of temperature compensation. Using a charger equipped with automatic temperature compensation can prevent both of these problems. This will not affect the performance of your DOLPHIN charger. You should not mix battery types because you are going to compromise a battery if you charge it at the wrong setting. On DOLPHIN PRO up-to 10 charging programs are available. For example in case of AGM batteries select the AGM charging programs. On DOLPHIN PRO up-to 10 charging programs are available. For example in case of AGM batteries select the AGM charging programs. Due to high level of electronic performance the DOLPHIN battery charger can provide full power without derating up to 65 degrees C.http://gabrielacalvente.com/userfiles/california-division-of-labor-standards-enforcement-policies-and-interpretations-manual.xml
On a DOLPHIN, you will NOT need to jumper the unused positive terminals to one of the positive terminals that you are using so that the charger will “read” a battery on each lead. On a DOLPHIN, you will NOT need to jumper the unused positive terminals to one of the positive terminals that you are using so that the charger will “read” a battery on each lead. We’ll use the typical 12-volt liquid lead acid battery as an example. The first charge stage would be the BULK stage which gets as much current into the battery as fast as possible without damage. The charger will attempt to discharge 14.4 volts at its maximum current in order to achieve the charge. Anything higher can cause heat build-up; lower will slow the charge rate. With this in mind, once the voltage differential equalizes (battery voltage meets the charger voltage, approximately 85% charged), we enter the absorption stage. In the absorption stage, the charger maintains the 14.4 volts, but the current will slowly drop as the battery increases in resistance (caused by an increase in charge level). Absorption stage will top off the battery state of charge. Once the battery is “full”, the charger will drop its voltage to 13.4 and transition to the float stage. The float voltage level is high enough to keep the battery “full”, even if DC loads are turned on, but low enough to prevent persistent gassing of the battery which can cause long term damage. Advanced microprocessor-controlled algorithms monitor the charging process to avoid battery damages caused by overcharging. Simply put, the charger collects information from the battery and adjusts the charge current and voltage based on this information. This allows the battery to be charged quickly, correctly, and completely when using a microprocessor-controlled battery charger. Because of this, fast charging does not have negative effects on the capacity of the battery and on battery cycle-life.
The multi-phase charging process ensures that each battery gets the power it needs in a manner that is best for the health of the battery ensuring that all of the energy is properly absorbed by the battery whether it’s a Conventional, AGM, Gel Cell, Marine or Deep Cycle battery. Microprocessor-controlled battery chargers can remain connected to the battery indefinitely and will not overcharge or damage it.Automatic chargers are more forgiving on the battery than manual chargers but are not designed for indefinite or maintenance use. Automatic chargers use a cycling process (see Maintain Mode) to prevent overcharging the battery. In this mode, the charger keeps the battery fully charged by delivering a small current when necessary. If the battery voltage drops below a preset level, the charger will go back in to Charge Mode until the battery voltage returns to the full charge level, which at this point the charger will return to Maintain Mode. The charger automatically switches between Charge Mode and Maintain Mode as necessary. The CHARGED LED will cycle on when the battery is at full charge and off when the voltage drops below a preset level and the charger goes into Charge Mode. The cycle will continue, and the CHARGED LED will stay on for longer periods of time as the battery becomes more fully charged. The voltage is maintained at a level determined by the BATTERY TYPE selected. On DOLPHIN PRO up-to 10 charging programs are available. For example in case of AGM batteries select the AGM charging programs. This will not affect the performance of your DOLPHIN charger. Based on the above equation it would therefore take you 5 hours to charge the battery. If you have more than one battery, you will have to add up the amp hour capacity of all the batteries and then divide it by the total amp output of the charger to get the charge time. This is why most of them now come with a 4-year warranty since November 2018 (3-year before Nov 2018).
Should you nevertheless experience trouble with your Dolphin Charger unit, please follow this simple, three-step procedure: This should do the trick. It doesn’t ? Go to Step Two Nothing wrong with your battery bank and electrical system. Then follow Step Three. You can find a dealer near you through our new interactive world map Cliquez ici: www.dolphin-charger.fr Click here. Battery Chargers Page 4 They are compati- ble with all types of generators currently available on the market. Acceptable voltage range is 98 - 130 Volts and 195 - 265 Volts. Regardless of the quality of shore power (weak shore power supply in high summer) your DOLPHIN 2 will work efficiently.These Battery Chargers have been programmed to automatically adapt themselves (without the need for manual intervention) to monophase vol- The 24 battery charger range is the most complete one on the inter- national market. The range begins with the small but highly talented 24V 10A and goes all the way to the very powerful 24V 400A which is capable of equipping even the most luxurious yachts. The larger chargers (80A plus) are described in the Superyacht section. Remote Control Panel O Thanks to the 10 charging positions, these chargers are suitable for use. We have paid special atten- tion to the time necessary to install this charger - it's fast. The features of this new Dolphin Battery Charger are synonymous with reliability and high efficiency and have a worldwide supported warranty and are insensitive to interna- tional differences in input voltage and frequency.Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates. The the elements ne installation. Built in fan Temperature sensor for battery compensation Clearly indicated access terminals cable output poi Battery Chargers Page 2 3 owing the ce of faults. Battery Chargers Page ah 5 Electrical cabinet This new concept combines AC circuit protection with a battery charger.
All have 2 or 3 outlets to provide charging for 2 or 3 separate banks if required. Our new generation of battery chargers - DOLPHIN 2 - provides our customers with technologically superior products. They are compatible with all types of generators currently available on the market. Acceptable voltage range is Volts and Volts. Regardless of the quality of shore power (weak shore power supply in high summer) your DOLPHIN 2 will work efficiently. Charging Programmes By internal switch for: 12V30A - 12V80A (DOLPHIN2) Dolphin 2 Dolphin 1 Remote Control Panel Dolphin 2: Suitable for the complete DOLPHIN2 range (from 12V 30A), this panel carries out the same functions as the display panel on the front of the charger. Dimensions: 120 x 65 mm (15 mm deep). The installer only has access to the components he needs to complete the installation or perform any modifications. All other components are protected by the housing. Warranty Dolphin Battery Chargers are protected by an international warranty against manufacturing faults for three years (providing they have not been used for purposes other than those intended by the manufacturers). These Battery Chargers have been programmed to automatically adapt themselves (without the need for manual intervention) to monophase voltages worldwide (115V 50 or 60 Hz - 230V 50 or 60 Hz 240V 50 Hz.). The 24 battery charger range is the most complete one on the international market. Thanks to the 10 charging positions, these chargers are suitable for use with all major battery types currently available on the market: Acid Free, Gel, Lead Calcium, 2V batteries. The enormous advantage of position 8 is the possibility it offers to use the charger as a stable Power Supply unit. This allows a stable and continuous power supply needed for certain on board equipment which need to be running constantly as well as prolonging the life of items such as light bulbs.
Charging Programmes By internal switch for: 24V20A to 24V50A (DOLPHIN 2) Dolphin 2 Remote Control Panel Dolphin 2: Suitable for the complete DOLPHIN2 range (from 12V 30A), this panel carries out the same functions as the display panel on the front of the charger. Dimensions: 120 x 65 mm (15 mm thick). In order to meet this increasing demand, Reya has produced a range of progressive chargers which allow users to change with their energy needs. Suitable for the complete DOLPHIN2 range (from 12V 30A), this panel carries out the same functions as the display panel on the front of the charger. We have paid special attention to the time necessary to install this charger - it s fast. The features of this new Dolphin Battery Charger are synonymous with reliability and high efficiency and have a worldwide supported warranty and are insensitive to international differences in input voltage and frequency. Aluminium casing with powder-coated treatment for a better corrosion resistance ISO 9001 assembling subcontractor 3 year warranty Charging programmes (12v40a only by means of an internal Switch position 00 Wet or flooded electrolyte batteries Switch position 01 Sealed lead batteries Switch position 02 Calcium-lead batteries Switch position 03 AC DELCO batteries Switch position 04 Yellow Top batteries switch) Switch position 05 Free lead batteries winterising Switch position 06 Sealed lead batteries winterising Switch position 07 Gel batteries Switch position 08 Power Supply Switch position 09 Inoperative Battery Chargers Page 13 The Smart Choice for Mission-Critical Engine Starting STI SERIES (STI200, STI300, STI500, STI700, STI1000) Power Frequency Pure Sine Wave Inverter The information This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest Sag Immunity, transient suppression and noise tolerant, the SDN series ensures compatibility in demanding applications.
Protection type: Total Power limit, Latch-style (Recovery after reset AC power ON or inhibit) Description. Features Technology for the Digital World. Match UPS. GE Digital Energy. This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest Voltronic Power Technology Corporation Adjust options: 1. Battery type selection. 2. Two battery charging priority(from 0-100%) 3. Charging LED Accessories. LED Power Supply Highly flexible electrical configuration Application: Product Features: This charger and tester is included in a series of professional chargers from CTEK Sweden AB and Sunteams 4000 Sunteams 5000 All shipped units are checked and documented in our testing Failure to follow the safety rules and other basic safety precautions With their MDRC profile and a width of only Direct connection to LG outdoor unit Telemecanique Sensor s OsiSense TM XUY photoelectric sensors The size and performance of these products make them the ideal choice for LED Product specific application. Relay monitored parameters 250 V DC 5 A DC Benefits of Solar Zamp Solar Portable Solar Kit Maximize Battery Life Electrical Independence Green, The output signal is proportional to measured frequency and is either load independent DC Current or load independent DC Voltage. It is connected to the EIB via the bus connecting terminal supplied. Further technical details are contained in section 3 or in the supporting technical manual available This unit is part of a range of professional battery chargers from CTEK SWEDEN AB. It represents the latest To use this website, you must agree to our Privacy Policy, including cookie policy. Our payment security system encrypts your information during transmission. We don’t share your credit card details with third-party sellers, and we don’t sell your information to others. Please try again.Please try again.Please try again later.
In order to navigate out of this carousel please use your heading shortcut key to navigate to the next or previous heading. Register a free business account Please try your search again later.Featuring 9 charging programs (including 2 winterizing and 1 power supply) depending on battery type, makes this charger suitable for All charging needs. Dolphin Pro can operate up to 65 C (149 F) without D rating.To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. If you continue to use this site we will assume that you are happy with it. Your personal data will be used to support your experience throughout this website, to manage access to your account, and for other purposes described in our privacy policy. Register 0 0 No products in the wishlist. Offer Sent! Your offer has been received and will be processed as soon as possible. Error: There was an error sending your offer, please try again. If this problem persists, please contact us. Float gives what the battery requires. 4. Power Supply: Charger “keeps up” with loads applied to the battery while it’s attached to AC power. Nevertheless, I like this one more than others. Here I’ve already downloaded seven files, and there were no fails. Recommended. I believe the download here is faster, and there are no ads at all. Services: Sync music, Manage music, Recover missing metadata, Record CDs Download MediaMonkey Now Buy MediaMonkey Gold Get Addons Never use any other conversion tool again. Find Music File Converter Mp3 Mp3 converter www.easypdfcombine.com Merge And Convert Files Into PDFs For Free With EasyPDFCombine App. It is your responsibility to provide references to bona fide sources. For a better experience, please enable JavaScript in your browser before proceeding.
It may not display this or other websites correctly. You should upgrade or use an alternative browser. As soon as I turn it on, the fan starts working. Since it’s located on the aft cabin, the one I use, this gets on my nerves. Now it’s winter! No reason. Is it like this or it’s malfunctioning? Cheers As soon as I turn it on, the fan starts working. Now it’s winter! No reason. Is it like this or it’s malfunctioning? CheersThey are, IMHO a great piece of kit. It does sound like your has developed a fault though. Presumably, it hasn't always done this. Is the unit very hot to the touch? As soon as I turn it on, the fan starts working. Now it’s winter! No reason. Is it like this or it’s malfunctioning? CheersThe point of night mode is silent operation. The charging rate will be reduced while in night mode. It's fairly quiet so has never caused us any problem and, of course, once we're out of the marina, it's dead anyway. However, as the recommended battery capacity is 400Ah, and I'm double that, I guess that might explain why the fan is always on.:ambivalence: Richard It's fairly quiet so has never caused us any problem and, of course, once we're out of the marina, it's dead anyway. However, as the recommended battery capacity is 400Ah, and I'm double that, I guess that might explain why the fan is always on.:ambivalence: RichardWhat's the recommended bank size for this 25a charger, do you know. I believe this is designed to charge 3 batteries (it has 3 output connections) but mine is actually charging 4: 1x80ah (engine) plus 3x100ah (service) batteries. My charger is the same as in this picture: What's the recommended bank size for this 25a charger, do you know. My charger is the same as in this picture: Smaller would take too long to recharge a heavily discharged battery. According to the advice on Dolphin's website 20% of the battery capacity would be the maximum.
Anyway, when I questioned this many years ago with Merlin the said the fan came on when the detected voltage reached a certain level. For instance, when mine is disconnected, the fan comes one when the the batteries are fully charged and the solar panel is working hard. Really odd first time I heard it out at sea.given we weren't connected to mains! Anyway, when I questioned this many years ago with Merlin the said the fan came on when the detected voltage reached a certain level. Really odd first time I heard it out at sea.given we weren't connected to mains!In order to sleep quite I turn the charging switch from the panel and it goes off. This is the only way to turn it off: by turning off the 'charging' switch on VDO panel (or switching off the shore power - I didn't know that this unit works with the engine working, so I never checked it). Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and otherThe information in this publication does notHII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental orThis document contains proprietary information that is protected by copyright. All rights are reserved. NoWeb Address: www.honeywellaidc.com. Trademarks. Dolphin, Dolphin RF, HomeBase, Mobile Base, and QuadCharger are trademarks or registeredMicrosoft, Windows, Windows Mobile, Windows CE, Windows NT, Windows 2000, Windows ME. Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks or registered trademarks of. Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of theirPatents. Please refer to the product packaging for a list of patents. Other Trademarks. The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell. Declaration for the Specification. All rights reserved.Chapter 1 - Agency Information. Label Locations.1-1. LED Safety Statement.1-2. Infrared LED Safety Statement.
1-2. UL and cUL Statement.1-2. Approvals by Country.1-2. For European Community Users.1-4. Waste Electrical and Electronic Equipment Information.1-4. Chapter 2 - Getting Started. Out of the Box.2-1. Today Screen.2-3. Navigation Bar.2-3. Command Bar.2-3. Icons in the Navigation Bar.2-4. Pop-Up Menus.2-5. Chapter 3 - Hardware Overview. Standard Configurations for the 9700.3-1. Peripherals for the 9700.3-2. Accessories for the 9700.3-3. Front Panel: 9700.3-4. Front Panel Features for the 9700.3-5. Back Panel: 9700.3-6. Back Panel Features for the 9700.3-7. Side Panels: 9700.3-8. Left Side.3-8. Right Side.3-8. Installing a Memory Card.3-9. Installing a SIM Card.3-9. Bottom Panel: 9700.3-10. Using the Touch Panel.3-11. Installing a Screen Protector.3-11. Healthcare Housing.3-12. Batteries.3-13. Main Battery Pack.3-13. Internal Backup Battery.3-14. Managing Battery Power.3-14. Checking Battery Power.3-15. Resetting the Terminal.3-16. Soft Reset (Warm Boot).3-16. Hard Reset (Cold Boot).3-16. Suspend Mode.3-16Overview. 4-1. Angled Imaging. 4-1. Image Engine Specifications. 4-1. Laser Specifications. 4-2. Supported Bar Code Symbologies. 4-2. Decoding. 4-3. To Decode a Bar Code. 4-3. Aiming Options. 4-4. Capturing Images. 4-5. Taking an Image. 4-5. Uploading Images. 4-6. Chapter 5 - Using the Keyboards. Available Keyboards. 5-1. Keyboard Combinations. 5-1. Common Buttons. 5-1. Using the Function Keys. 5-2. Using the Modifier Keys. 5-3. Using the Navigation Keys. 5-3Chapter 6 - System Settings. Overview. 6-1Buttons. 6-4. Input. 6-5. System Menu. 6-7. About. 6-8. Backlight. 6-8. Certificates. 6-9. Encryption. 6-9. Error Reporting. 6-9. External GPS. 6-10. Managed Programs. 6-10. Memory. 6-11Regional Settings. 6-13. Remove Programs. 6-13. Screen. 6-15. Task Manager. 6-16Connections Menu. 7-1. Using the IrDA Port. 7-2. IrDA Port Location. 7-2. Sending Data. 7-2. Receiving Data. 7-3. Connections Manager. 7-4. To Access the Connections Manager. 7-4. Task Tab. 7-4. Advanced Tab. 7-5.
Dolphin Wireless Manager. 7-6. Dolphin Wireless Manager Window. 7-6. Enabling the Radios. 7-6. Accessing Radio Configuration Utilities. 7-7. ActiveSync Communication. 7-8. Installing Additional Software. 7-10. Adding Programs to the Terminal Using ActiveSync. 7-10. Adding Programs Directly from the Internet. 7-11Chapter 8 - Working with GSM. Overview. 8-1. Quad Band Antenna. 8-1. SIM Card Installation. 8-2. Enabling the GSM Radio. 8-4. Voice Communication. 8-5. Audio Modes. 8-5. Volume Control. 8-5. Accessing the Dialer Window. 8-5. Dialing. 8-5. Sending Calls. 8-6. Ending Calls. 8-6. Keyboard Combinations for Calls. 8-6. View Options. 8-6. Setup Options. 8-7. Data Communication. 8-8. Establishing Data Communication. 8-8. Ending the Data Connection. 8-10. Roaming. 8-11. Chapter 9 - Working with the Bluetooth Radio. Enabling the Bluetooth Radio. 9-1. Connecting to Other Bluetooth Devices. 9-2. Pairing and Trusted Devices. 9-4. Types of Devices and Services. 9-5. Connecting to Bluetooth Printers. 9-6. Connecting to Bluetooth Headsets. 9-6. Transferring Files. 9-7. Making the Terminal Discoverable. 9-8Chapter 10 - Working with GPS. Overview. 10-1. Assisted GPS Support. 10-1. Powering the GPS Module. 10-1. Communication Ports. 10-2. Selecting the Port. 10-2GPS Demo. 10-3. Chapter 11 - Dolphin 9700 HomeBase Device. Overview. 11-1. Parts and Functions. 11-2. Power. 11-4. Serial Connector. 11-5. Charging the Main Battery. 11-6. To Power a Terminal and Charge its Main Battery. 11-6. Charging a Spare Battery in the Auxiliary Battery Well. 11-6. Communication. 11-7. Connecting the Communication Cables. 11-7. Establishing Communication. 11-7. Communicating with the Dolphin Terminal. 11-7. Verifying Data Transfer. 11-8. RS232 Communications Cables. 11-9. RS232 Pin Configuration. 11-9. Mounting. 11-10. Desk Mounting. 11-10. Wall Mounting. 11-11. Chapter 12 - Dolphin 9700 Mobile Base Device. Overview. 12-1. Front Panel. 12-2. Bottom Panel. 12-3. Powering the Dolphin Terminal.
12-4. Charging the Dolphin Terminal. 12-4. Mounting. 12-5. Power. 12-6. Establishing Communication. 12-7. Connecting the Communication Cables. 12-7. Establishing ActiveSync Communication. 12-7. Chapter 13 - Dolphin 9700 ChargeBase Device. Overview. 13-1. Parts and Functions. 13-2. Supplying Power. 13-3Charging Terminals. 13-4. Mounting. 13-5. Chapter 14 - Dolphin 9700 QuadCharger Device. Overview. 14-1. Parts and Functions. 14-2. Supplying Power. 14-3. Inserting and Removing Battery Packs. 14-4. Charging Batteries. 14-4. Using the Battery Analyzer. 14-5. Mounting. 14-6. Desk Mounting. 14-6. Wall Mounting. 14-7. Troubleshooting. 14-8. Chapter 15 - Customer Support. Product Service and Repair. 15-1. Online Product Service and Repair Assistance. 15-1. Technical Assistance. 15-2.