highpoint rocketraid 2320 manual

highpoint rocketraid 2320 manual

Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. This document contains materials protected by International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed in any form and for any purpose without the express written permission of HighPoint Technologies, Inc. Product names or brand names appearing in this manual may or may not be registered trademarks or copyrights of their respective owners. Backup your important data before using HighPoint’s products and use at your own risk. In no event shall HighPoint be liable for any loss of profits, or for direct, indirect, special, incidental or consequential damages arising from any defect or error in HighPoint’s products or manuals. Information in this manual is subject to change without notice and does not represent a commitment on the part of HighPoint. HighPoint assumes no liability for technical inaccuracies, typographical, or other errors contained herein. Disks must be initialized before configuring them into RAID arrays. The initialization process will destroy all data on the disk. Non-redundant arrays (RAID 0, JBOD) do not need to be initialized. The initialization process can be completed after installing the driver and management software. The array is not accessible by the operating system until initialization is complete. For RAID 1 and RAID 10 arrays, initialization will results in data being duplicated identically to the mirror pair. For RAID 5 arrays, initialization will result in parity being generated from all array members. A RAID 5 array, however, is not fault-tolerant until initialization is finished. Any number of disks can be added to an array, at any time. Data can be accessed and utilized even while being redistributed. Data is still accessible during the migration process, and a base level of security is still active.http://proia.bg/userfiles/haynes-manual-freelander-download.xml

• highpoint rocketraid 2320 manual, highpoint rocketraid 2320 manual user, highpoint rocketraid 2320 manual download, highpoint rocketraid 2320 manual driver, highpoint rocketraid 2320 manual troubleshooting.

Spare disks may also be members of a RAID array. Any available space on these disks may be used to rebuild other broken arrays. A legacy disk attached to the RocketRAID 2320 can be accessed by the operating system, but cannot be used to create RAID arrays. A legacy disk must be initialized before assigning it to an array. The SATA port furthest away from the surface of the adapter is always the odd numbered channel (1, 3, 5, 7), while the port closest to the adapter is the even numbered channel (2, 4, 6, 8). The RocketRAID 2320 includes a cable designed for use with these jumpers. Consult the Single-RAID Cross Adapter section (page 2-4) for more information. Consult the chassis’s manual for more information. The following diagrams describe the connector pin definitions for the Disk Activity jumpers (J2, J3), and Disk Failure connections (J4, J5). The “Ports” refer to the RocketRAID 2320’s eight SATAII channels. It may be necessary to attach the low-profile bracket in place of the standard bracket, depending upon the chassis design. Each RocketRAID 2320 included eight SATA cables, and supports up to eight separate hard disks drives. For these system chassis, cables are attached to the chassis backplane, rather than directly to each individual hard disk. Consult the chassis’s manual for proper installation procedures. If the system detects the presence of the adapter, the RocketRAID 2320 BIOS Utility will be displayed during bootup. Make sure all attached disks are detected by this utility. If any of the hard disks are not detected, power down the system and check the power and SATA cable connections. Up to sixteen hard disks can be assigned to a single RAID array. This feature is referred to as “Single-RAID Cross Adapter” support. JP3 is a 3-pin jumper, while JP4 is a 4-pin design.http://advancedpropertymanagementinc.com/userfiles/haynes-manual-ford-transit-connect-pdf.xml

Insert one end of the cross-adapter cable into the appropriate jumper on the first adapter (3-pin connector to JP3, 4-pin connector to JP4), and the remaining connector into the appropriate jumper on the second adapter. There is no particular connector-to-jumper requirement. Any given connector can be inserted into the corresponding jumper on either card. These commands are displayed towards the top of the utility’s interface. Use the ENTER key to execute the selected command. Section 2 discusses this command in detail. The controller is capable of using spare disks to automatically rebuild broken or faulted RAID arrays. Enabling staggered drive spin up will power up the hard disks one at a time, approximately every two seconds. Press the ENTER key to change the view. Next, press the Y (yes) key to initialize the selected disk(s), or N (no) key to cancel the initialization process. The array name dialogue box will appear. Use the keyboard to input a new Array Name, and press the Enter key. The array can be named at a later time, and the name of the array can be changed at any time. A device list will appear, and display all available hard disk drives. After all of the disks have been selected, press the ESC key to return to the Create Menu. The total available capacity will be displayed. Press ENTER if you wish to use all available space. The Capacity option allows you to set aside disk space that be used to create another array, set as a spare disk, or partitioned to act as a single disk (by the operating system). Press the Y (yes) key to create the array, or N (no) key to cancel the creation process. Each RAID array can support up to 16 hard disks, and these disks can be attached to as many as 4 separate RocketRAID 2320 adapters. The BIOS utility menu will display disks attached to each RocketRAID 2320 adapter installed into the system. Use the Page Up and Page Down keys to scroll through available hard disks.

If the disks in question are part of a RAID array that did not utilize the full available capacity at the time of creation, these disks may be used as spares. In this example, 200GB of disk space remains unallocated. This unallocated space would allow these disks to be set as spares for a separate redundant array that falls into the same capacity range (200GB). The program should start automatically. This document contains materials protected by International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed in any form and for any purpose without the express written permission of HighPoint Technologies, Inc. Trademarks Companies and products mentioned in this manual are for identification purpose only. Page 3 Table of Contents Table of Contents Chapter 1 Introduction About this Guide. 1-1 Introducing the RocketRAID 2320 Host Adapter. 1-1 Product Features. 1-1 Understanding RAID Concepts and Terminology. Page 5 Chapter 1 Introduction Contents of this Chapter: About this Guide Introducing the RocketRAID 2320 Host Adapter Product Features Understanding RAID Concepts and Terminology Page 6 Introduction About this Guide The RocketRAID 2320 SATAII Host Adapter’s User’s Guide provides information about the functions and capabilities of the host adapter, and instructions for installing, configuring and maintaining RAID arrays hosted by the adapter. Introducing the RocketRAID 2320 Host Adapter The HighPoint RocketRAID 2320 is an 8-channel PCI-Express to Serial ATA II RAID controller. Page 7 Introduction Understanding RAID Concepts and Terminology The following concepts and terminology is commonly used when describing the functions of the RocketRAID 2320 Host Adapter. Disk initialization Initializing a disk writes necessary RAID configuration information to that disk. Disks must be initialized before configuring them into RAID arrays. The initialization process will destroy all data on the disk.

Disk Status New The disk contains no data and has not been initialized. Page 8 Introduction Foreground initialization Foreground initialization will zero-out all data on the array. The array is not accessible by the operating system until initialization is complete. Background initialization Background initialization allows the array to be used immediately. For RAID 1 and RAID 10 arrays, initialization will results in data being duplicated identically to the mirror pair. For RAID 5 arrays, initialization will result in parity being generated from all array members. Page 9 Introduction Spare disk A spare disk is a single disk that can be used to automatically rebuild a redundant array in case of drive failure. Spare disks may also be members of a RAID array. Any available space on these disks may be used to rebuild other broken arrays. Legacy disk Disks attached to the RocketRAID 2320 that contain valid partition tables will be identified as legacy disks. The SATA port furthest away from the surface of the adapter is always the odd numbered channel (1, 3, 5, 7), while the port closest to the adapter is the even numbered channel (2, 4, 6, 8). The following diagrams describe the connector pin definitions for the Disk Activity jumpers (J2, J3), and Disk Failure connections (J4, J5). The “Ports” refer to the RocketRAID 2320’s eight SATAII channels. The RocketRAID 2320 includes both standard and low-profile brackets. Each RocketRAID 2320 included eight SATA cables, and supports up to eight separate hard disks drives. Many server-level chassis include hard-disk hot-swap bays. Example installation: For a 16-hard disk, 2-card cross-adapter RAID configuration, install a second card into the next available PCI-Express slot. This command should be displayed automatically when the RocketRAID 2320’s BIOS screen appears during the system’s boot up procedure. 1 - BIOS Command Overview The RocketRAID 2320 BIOS Utility provides a wide selection of RAID related commands.

These commands are displayed towards the top of the utility’s interface. The controller is capable of using spare disks to automatically rebuild broken or faulted RAID arrays. Section 3 discusses this command in detail. Settings Set Boot Mark - this function is used to designate a particular disk or RAID array to function as the RocketRAID 2320’s boot device. Page 19 RocketRAID 2320 BIOS Utility 2 - Creating RAID Arrays Initializing Disks: Before creating a RAID array, the disks must be initialized. Initialization writes necessary RAID configuration information to the hard disk. Use the arrow keys to select the Initialize command, and press ENTER. Warning: Initialization will destroy all pre- existing data on the selected hard disks. Page 20 RocketRAID 2320 BIOS Utility 6. 7. Next, use the v arrow key to highlight the Capacity (GB) option and press ENTER. The total available capacity will be displayed. Press ENTER if you wish to use all available space. Note: Multiple arrays can be created using the same set of hard disk drives. Spare Disks are used to automatically rebuild Redundant RAID arrays (RAID 1, 5, 10) in the case of disk failure. To remove the Spare Disk setting from a hard disk, highlight the spare disk, and press ENTER. Page 22 Chapter 4 RocketRAID 2320 Driver and Software Installation Microsoft Windows (2000, XP, 2003 Server) Contents of this Chapter: Driver and Software CD Windows Driver Installation Page 23 RocketRAID 2320 Driver and Software Installation Driver and Software CD The RocketRAID 2320 retail box includes a Driver and Software CD. The program should start automatically. Insert a blank floppy diskette into the system’s floppy drive. Click on “Create Driver Diskette”. Page 24 RocketRAID 2320 Driver and Software Installation Click on the “Please Select the Diskette you want to create” drop-down button, and select the appropriate OS from the list. Click on the “OK” button to create the driver diskette.

Page 25 RocketRAID 2320 Driver and Software Installation To install the RAID software: Click on “Install RAID Management Software”. Select the desired software from the drop down menu, and click on the “OK” button. Page 26 RocketRAID 2320 Driver and Software Installation Windows Driver Installation Before installing the RocketRAID 2320 device driver, make sure the RocketRAID 2320 host adapter and all required hard disks have been installed into the system’s chassis (refer to the Hardware Installation section, page 2-3). Page 27 RocketRAID 2320 Driver and Software Installation 2. 3. In the popup window, select Hardware tab and then click Device Manager button. Double click the “SCSI and RAID controllers” entry. If the RocketRAID 2320 device entry is not displayed, or there are “?” or “!” marks displayed near the RocketRAID 2320 entry, the driver has not been installed properly. Delete the entries and reinstall the driver. The software is incapable of working with RAID arrays or hard disks attached to the RocketRAID 2320 until the user has logged on. Default Parameters: System Address: 127.0.0.1 Port: 7402 User Name: RAID Password: hpt Note: The password and user name fields are case sensitive. The first time the software is used, make sure to enter the information listed above. Page 30 RocketRAID 2320 Driver and Software Installation Operation This menu will list all available commands for the selected Function menu. Page 31 RocketRAID 2320 Driver and Software Installation 3. 4. 5. Select the desired RAID level from the drop-down list. Enter a name for the array using the keyboard (this is optional), and click the Next button. If you are creating a redundant array (RAID 1, 5, 10), select an initialization option. If you are creating a RAID 0 or JBOD (volume), skip to step 6: For RAID 1 and RAID 10 arrays, the default initialization method is “No initialization”.

Page 32 RocketRAID 2320 Driver and Software Installation Press Enter to use the default value (the maximum capacity for the array), or specify the desired value using the keyboard, and press Enter to confirm this selection. Then, click the Finish button. Note: If you have specified an initialization option, the initialization process will start automatically. Page 33 RocketRAID 2320 Driver and Software Installation 5 - Configuring Spare Disks Spare disks can be used to rebuild redundant RAID arrays in the case of failure. To configure spare disks, highlight the “Management” menu, and select the “Spare Management” function. The Spare Management window will appear. To add a spare disk, select it from the Available Disk list box and click the button to add the disk to the Spare Pool list box. Page 34 RocketRAID 2320 Driver and Software Installation 2. 3. Highlight the array that needs to be rebuilt. Click the Rebuild button on the toolbar or select the “Rebuild” command from the “Operation” menu. Verifying an Array For a RAID 1 or RAID 10 array, the verify process compares the data of one mirror pair with the other (single hard disk in the case of RAID 1, and a paired set of disks for RAID 10). For RAID 5, the verify process calculates RAID 5 parity and compares it to the parity data on the array. The interface is very similar to the Array Creation Wizard interface. Page 36 RocketRAID 2320 Driver and Software Installation 8 - Misc. To access the Device Management window, highlight the “Management” menu, and select the “Device Management” function. Page 37 RocketRAID 2320 Driver and Software Installation SAF-TE Management This feature allows the administrator to view and monitor a variety of SAF-TE related attributes, such as chassis temperature readings, disk failure, and the status of the chassis cooling apparatus (cooling fans). Renaming an Array 1. Highlight the “Management” menu, and select the “Array Management” function.

Page 38 RocketRAID 2320 Driver and Software Installation 9 - Managing Events The HighPoint RAID Management Console will log all events that have occurred on any host adapter under it’s control. Viewing Logged Events To view logged events: 1. Highlight the “View” menu, and select the “Event View” option. 2. In the Event View window, you can filer events, clear events, and save events to a file. Configuring E-mail notification To enable E-mail notification: 1. 2. 3. Page 39 RocketRAID 2320 Driver and Software Installation To add a Recipient: 1. 2. 3. 4. Highlight the “Management” menu, and select the “Event Notification” function. Click the “Add” button on the toolbar or select “Add” command from the “Operation” menu. Enter the necessary information in the Add recipient window. The recipient will be listed in the main window. You can use Modify or Delete button on the toolbar to modify or delete the recipient. To test E-mail notification: 1. Page 40 RocketRAID 2320 Driver and Software Installation To setup and schedule tasks highlight the “Management” menu, and select the “Task Management” function to open Task Management window. The Task Schedule list displays all of the tasks assigned to the selected remote system. To view detailed information about a specific task, highlight and Double-click the task’s name. Add a Scheduled Task This command is used to add a Scheduled task for the selected remote system. Page 41 RocketRAID 2320 Driver and Software Installation Select the task type and the array that you want to verify or rebuild, then click “Next”. Page 42 RocketRAID 2320 Driver and Software Installation Enter a name for the task. Configure the frequency for the task. Set the duration for the task. Check the “Enable the task” option to activate this task. Click “Finish”. Modify a Scheduled Task This command is used to change settings for a scheduled task. To Modify a Task Schedule: 1. 2. Select a task from the Task schedule list.

Click the “Modify” button on the toolbar, and modify the task settings in the popup window. Page 43 RocketRAID 2320 Driver and Software Installation 10 - Configuring Remote Systems Then HighPoint RAID Management Console manages a RAID controller through a connection to the HighPoint RAID Management Service, which runs on the system where the RAID host adapter is physically installed. This type of system is referred to as a “remote system”. Note: What the software classifies as a “remote system” may not always be an actual remote computer. Page 44 RocketRAID 2320 Driver and Software Installation Modify a Connection This command modifies connection information for a remote system. To modify a connection: 1. 2. 3. Highlight the “File” menu and select the “Remote Control” function. Highlight the system you want to modify. Click the Modify button on the toolbar or select the “Modify” command from the “Operation” menu. 4. Enter new connection information in the popup window, and click OK to apply the changes. Page 45 RocketRAID 2320 Driver and Software Installation 3. Click the “Connect” button on the toolbar or select the “Connect” command from the “Operation” menu. 4. Enter the appropriate Login information in the popup window. You are free to modify the username and password after the connection is established. Page 46 RocketRAID 2320 Driver and Software Installation System Configuration This function is used to modify the service configuration on a remote system. To change the service configuration: 1. 2. 3. 4. Highlight the “File” menu and select the “Remote Control” function. Highlight the remote system you want to modify. Select the “System Configuration” option from the “Operation” menu. Modify the information in the popup window. Page 47 RocketRAID 2320 Driver and Software Installation 11 - Configuring Users and Privileges The RAID Management Console allows the Administrator to manage user accounts in its own database.

You can setup multiple users and assign different privileges levels for the purpose of RAID management. Users can be assigned to each individual Remote System controlled by the RAID Management Console. Page 48 RocketRAID 2320 Driver and Software Installation 3. 4. Select the appropriate privileges for the user. Click “Finish”. Delete a User This function deletes a user’s account on the connected remote system. To delete a user: 1. 2. Select the target user ID from the User list displayed in the User Management window. Click Delete to remove the selected user. Click “Yes” to delete the item. Select “No” to cancel this command. Page 49 RocketRAID 2320 Driver and Software Installation 1. 2. 3. Select the target user ID from the user list displayed in the User Management window. Click the “Set Password” option, and enter the password for the user. Click OK to apply your selections. Set Privilege The Administrator uses this function set a user’s privileges for the selected remote system. To set privileges for a user: 1. 2. Select the target user ID from the user list displayed in the User Management window. Page 50 Chapter 5 Linux Driver Support Contents of this Chapter: Fedora Core 3 Linux installation Overview Red Hat Enterprise 3 Overview SuSE Linux Enterprise Server (SLES) installation Overview Page 51 Linux Driver Support 1 - Fedora Core 3 Linux installation Overview This section provides instructions describing how to install and utilize the RocketRAID 2320 Adapter on a Fedora Core 3 Linux system. 2 - Installing Fedora Core 3 on the RocketRAID 2320 Host Adapter Note: If the OS is running kernel that differs from the one supported by the precompiled driver, the precompiled drivers cannot be used. A driver can be built for this kernel using the OpenSource package for the RocketRAID 2320 controller. Page 52 Linux Driver Support 2) At the “Welcome to Fedora Linux” installation screen, a prompt labeled “boot:” will appear at the bottom of the screen.

Type in linux dd, then press Enter.Page 55 Linux Driver Support 1 - Red Hat Enterprise 3 Overview This section provides instructions describing how to install and utilize the RocketRAID 2320 Adapter on a Red Hat Enterprise 3 Linux system. 2 - Installing Red Hat Enterprise 3 (AS, ES, WS) Linux on the RocketRAID 2320 controller To install Red Hat Enterprise Linux onto disks or RAID arrays attached to RocketRAID 2320: Step 1 Prepare the Driver Diskette The driver is provided in a floppy diskette image file format. Page 56 Linux Driver Support 1. 2. The system will now load the RocketRAID 2320 driver automatically. When prompted “Where do you want to install the boot loader? ” in the “Boot Loader Configuration” dialog, select “Master Boot Record (MBR)” to instruct the system be to boot from the RocketRAID 2320. Continue the installation as normal. You can refer to Red Hat Enterprise Linux installation guide. Note: The system device mapping order is the same as the order shown in RocketRAID 2320 BIOS Setting Utility. Page 60 Linux Driver Support 1 - SuSE Linux Enterprise Server (SLES) installation Overview This section provides instructions describing how to install and utilize the RocketRAID 2320 Adapter on a SuSE (SLES) Linux system. 2 - Installing SLES Linux on the RocketRAID 2320 Host Adapter Note: If the OS is running kernel that differs from the one supported by the precompiled driver, the precompiled drivers cannot be used. Page 61 Linux Driver Support 4. 5. 6. When the “Diver Update Menu” is displayed, press “OK” and “back” for back to installer. Next. Select “back” to return to the installer. Installation will now proceed normally. Refer to SLES Linux documents for additional OS installation procedures. Additional Installation Notes: The system device mapping order is the same as the order shown in RocketRAID 2320 BIOS Setting Utility. YAST is a graphical configuration utility that is capable of executing the commands described below.

We recommend using YAST, if available, as it may help simplify the installation process. Example: A RAID array has been configured between several hard disks. Page 65 Chapter 6 FreeBSD Driver Support Contents of this Chapter: 1 - Installing FreeBSD on the RocketRAID 2320 Controller 2 - Installing RocketRAID 2320 Driver on an Existing System 3 - Updating the Driver 4 - Uninstalling the Driver Page 66 FreeBSD Driver Support 1 - Installing FreeBSD on the RocketRAID 2320 Controller If you would like to install FreeBSD onto arrays attached to the RocketRAID 2320 host adapter, please follow the steps below. Step 1 Prepare the Driver Diskette When installing FreeBSD to a disk or array attached to the RocketRAID 2320, you must prepare a RocketRAID 2320 driver diskette before starting the installation procedure. First, obtain the driver diskette image file from the driver package. Type in “boot” and continue with installation as normal. Page 70 FreeBSD Driver Support 7. Before exiting installation, an additional step must be taken to copy the RocketRAID 2320 driver module to the system. On the driver diskette, there is a setup script labeled “postinstall”, which will complete this task. Page 74 FreeBSD Driver Support 3 - Updating the Driver To update the driver with a newer revision, simply reinstall the driver following the steps discussed in the previous section, “Install the driver on an existing system”. 4 - Uninstalling the Driver The driver can only be uninstalled when the system is not booting from devices attached to the RocketRAID 2320 controller. Page 75 Appendix Customer Support Page 76 Customer Support Customer Support If you encounter any problems while utilizing the RocketRAID 2320, or have any questions about this or any other HighPoint product, feel free to contact our Customer Support Department.

Troubleshooting Checklist Before contacting our Customer Support department: Make sure the latest BIOS, driver and RAID Software have been installed for the RocketRAID 2320. Updates are available from our website. Page 77 FCC Part 15 Class B Radio Frequency Interference statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. RocketRAID RocketRAID User Manual highpoint 2320 manual Download Download Download Download Datasheet Download Download. View here the highpoint 2320 manual free Highpoint RocketRAID manual. Have you read the manual but does it answer your question. Then ask your question on this page to other Highpoint RocketRAID owners. Here's where you can download Free. We show only the top products per product group at this page. HighPoint Turbo-RAID Technology: For over a decade, HighPoint has strived to take the cost and complexity out of RAID. A progress bar will be displayed towards the bottom of the interface window, and will indicate the % completion, and provide an estimate of the time needed to complete the initialization View here the free Highpoint RocketRAID manual. The HighPoint RocketRAID PCI Express to SATA IIRAID Controller is the next generation for high performance computing x. Hi all, I've just switched over to FlexRAID RAID-F from having previously used a HighPoint RocketRAID with RAID 5, partly due worries about the card maybe not having too many years left in it, and partly due to an OCE gone wrong with the leaving me not trusting it for RAID functions. Read honest and unbiased product reviews from our users.

Followed the instructions in the provided manual to the dot, and found the drivers didn't do anything other than cause windows to crash. HighPoint Rocket 640L Manuals. Select the appropriate HighPoint Rocket 640L manual from the list on this page, download it or check online. Screen Document Information Share in Social HighPoint Rocket 640L Quick installation Manuel d'utilisation Highpoint RocketRAID - l’avez vous jamais perdu. Si vous venez ici, probablement le cas. Cependant, vous pas le seul qui a des avec le stockage des manuels d’utilisation de tous les.I purchased a 2nd highpoint from pricepoint computers. Ive decided to copy some data from array to array 2. At array is only made up of 5hdds, so speeds arnt quite as good as the hdd array. Supporting up to SATA II and SATA I hard drives, the Highpoint RocketRAID PCI Express controller card is perfect for entry-level storage servers. Supporting RAID 0, 1, 5, 10, and JBOD, the RocketRAID can not only. The adapters I used in particular are the,, and yes, I used highpoint controllers for many years as servers for home use and small business. As of FreeNAS build and newer the entire 35xx and 43xx. So yesterday I got my new HighPoint RocketRAID PCI Express x RAID card. Link Finally, I was going to have a nice fast RAID 5, or so I was thinking. ManualsWorld??? Using RocketRAID for Software RAID User Name Remember Me. Password Linux - Hardware This forum is for Hardware issues. Having trouble installing a piece of hardware. Want to know if that peripheral is compatible with. Setting up a RocketRaid controller on Linux Mint July 4, Jake B Hardware, Jake B, Linux Mint, Tutorial After the most recently recorded podcast, I decided to take a stab at running Linux on my primary media server. Highpoint Sterownik manuals. Sterownik i przejrzyj lub zadaj pytanie innym produktu. Tutaj znajdziesz wszystkie instrukcje Highpoint. Wybierz jeden z aby HighPoint ?HighPoint Windows??? WindowsHighPoint??.