jx300+canon+manual

jx300+canon+manual

FAX-L280 User Manual All rights reserved. No part of this publication may be reproduced, transmitted, or copied in any form whatsoever without expressed written permission from Canon Inc. Trademarks Canon is a registered trademark of Canon Inc. See “Printing a Document in Memory” on page 35 See “Replacing a FINE Cartridge” on page 57 See “Aligning the FINE Cartridge”. Note This guide contains information for four Canon models. Please note that the illustrations of the fax in this guide may differ from your model. Instructions for specific models are labelled with the fax names. Introduction. Do not attempt to use the machine in any way not described in this manual. Warning This product emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities, please move away from this product and consult your doctor. Do not install the machine in locations that are very humid or dusty, in direct sunlight, outdoors, or close to a heating source.Turning on the Machine Before turning on the machine, confirm that the FINE Cartridge is set into place. Note If preparatory operations are not yet finished, follow the Easy Setup Instructions to complete them.Button Uppercase Letter Lowercase Letter Number Mode Mode (:A) Continue entering other letters or numbers using the numeric buttons.Thus, whenever you send a fax from this machine, the recipient receiving the fax knows who sent it, and when it was sent. Setting Daylight Saving Time (Summer Time) Some countries adopt the daylight saving time (summer time) system that shifts the clock time forward or back at certain periods of the year. The maximum size of document that can be loaded is 216 mm wide by 400 mm long. You can use regular copier paper, cotton bond paper, or typical letterhead. Your fax does not require special ink jet paper. Always use paper without curls, folds, staples, or damaged edges. Look at the label on the package to see if the paper has a preferred side for printing.

• canon jx300 manual, fax jx300 canon manual, jx300 canon manual, jx300 canon manual printer, jx300 canon manual user, jx300 canon manual software, jx300 canon manual driver.

Insert the stack face up into the Multi- Purpose Tray (1), and align the right edge of the stack with the right side of the Multi- Purpose Tray. Then slide the Paper Guide (2) snugly against the left edge of the stack. You can make up to 99 copies of one document at a time.You can send up to 20 A4-size (10 legal-size) pages at a time (based on the Canon FAX Standard Chart No.1, standard resolution). You cannot add pages while the fax is sending. See “Jams in the Document Tray” on page 65. Automatic Redialing What is Automatic Redialing. When you are sending a document and the receiving party’s line is busy, the fax waits the specified time and then dials the same number again. Sending Other Documents While the Fax is Set for Delayed Sending You can send, receive, and copy other documents even when the fax is set for sending at a preset time. To send or copy other documents after setting the fax for delayed sending, simply send or copy using any other sending procedure in this guide. To determine which mode best suits your requirements, see the table below. Receives documents automatically and rings for voice calls RECEIVE (see page 28). If the Ink Lamp lights up faxes will be received to memory. Receiving Documents Manually: MANUAL MODE Check that. If you subscribe to this service, your line is assigned two numbers: one for fax and one for phone. When the fax number is called, the network sends a specific ringing tone which your fax recognizes and automatically handles as a fax call. If you subscribe to this service, your line is assigned two numbers: one for fax and one for phone. When the fax number is called, the network sends a specific ringing tone which your fax recognizes and automatically handles as a fax call. Receiving to Memory Temporarily You can enable memory receiving feature temporarily. The fax starts receiving documents in memory.Use one of the dialing methods described. Your fax begins receiving the document.

If you set to, the setting goes on to the next setting. If you set to or, the setting returns to. Only one outgoing message, no longer than 20 seconds, can be recorded. The fax returns to standby mode. Note You cannot delete the. To record a new outgoing message, repeat steps 1 to 7. The old outgoing message will be automatically deleted when you record your new message. The recording time can be set to 0, 60, 120 or 240 seconds.Recording Voice Memos Use this feature when you are going out and want to leave a message for another member of the family. You can also use the remote control features to set. You must register a four-digit PIN as your password before you can use these features.However, if is set to (see page 52), it is not necessary to enter your password when you use the feature (see page 45). If you enter an invalid password, you will hear an error tone. You can use remote control to access the forwarding number and listen to your telephone messages. Setting PIN ENTRY If you set setting to, you must enter a password to use the forwarding feature (see page 46). If forwarding is still not possible after the fax redials the forwarding number the specified number of times, the forwarding setting will be temporarily canceled. Each menu contains settings that control different functions of your fax. Coded Speed Dialing List Lists the numbers and names registered under coded speed dialing codes. User’s Data List Lists the current settings of the fax and the registered sender information. List of Documents in Memory Lists the documents currently stored in the fax’s memory (see page 35). Menus CS CLEANING (see page 62) NOZZLE CHECK (see page 58) CLEANING (see page 59) DEEP CLEANING (see page 59) ALIGN PRINT HEAD (see page 60) HEAD ALIGN VALUE (see page 60) ROLLER CLEANING (see page 63) BOTTOM CLEANING (see page 63) When printing is finished, replace the FINE Cartridge immediately.

If you continue printing with an empty FINE Cartridge, it will be a cause of trouble. Setting Automatic Printing When the ink is low, you can set the receiving fax either automatic printing or storing in memory.If you need to unplug the fax, wait until it returns to standby mode (time and receive mode displayed on the LCD). Please be advised that Canon shall not be liable for any malfunction or trouble which may be caused by continuation of printing under the ink out condition. Testing and Cleaning the FINE Cartridge The print head in the FINE Cartridge contains nozzles through which ink is propelled onto the paper. The fax prints the nozzle check pattern. Nozzle check pattern If the pattern is broken or missing (1), clean the FINE Cartridge print head (see page 59). FINE Cartridge Cleaning If the pattern is broken or missing, clean the FINE Cartridge print head. If cleaning does not improve print quality, replace the FINE Cartridge (see page 57). Aligning the FINE Cartridge If ruled lines are printed misaligned or print results are otherwise unsatisfactory, adjust the print head position. Dirt and dust particles that collect on the underside of the Printer Cover affect the quality of the documents you copy or send. Cleaning the paper feed roller will wear the roller, so perform this only when necessary. Ensure that the machine is turned ON and there is no paper loaded in the Multi- Purpose Tray. If dust or dirt can be seen on the paper, repeat the cleaning process. Cleaning The Protrusions Inside The Machine If protrusions inside the machine are stained, wipe ink off the protrusions using a swab or something similar. Note You do not need to unplug the fax when clearing document jams. When. Gently remove the jammed paper inside the fax.Make sure the paper stack is loaded properly in the Multi-Purpose Tray, and that the Paper Guide is adjusted correctly (see the Easy Setup Instructions).

Sheets of paper may be sticking Be sure to fan the paper stack before loading it in the Multi-Purpose Tray. You may be printing on the wrong side Some papers have a “right”. If the same error occurs, contact a Canon service representative. !!CHECK!! 5B00. CHECK PAPER SIZE Cause Action. Replace the FINE Cartridge be correctly detected. (see page 55). MEMORY FULL Cause Action The fax’s memory is full because it has Print and delete any documents stored in memory (see page 35). If the same error occurs, contact a Canon service representative. Troubleshooting. Specifications. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Under power fail conditions, this telephone may not operate, Please ensure that a separate telephone, not dependent on local power, is available for emergency use.All rights reserved. Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that the software was developed by the University of California, Berkeley. For details on FINE Cartridge replacement, refer to “Replacing A FINE Cartridge” in this guide. Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Canon FAX-JX300 owners to properly answer your question. Ask a question About the Canon FAX-JX300 This manual comes under the category Fax machines and has been rated by 1 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Canon FAX-JX300 or do you need help. Ask your question here Canon FAX-JX300 specifications ManualSearcher.com ensures that you will find the manual you are looking for in no time.

Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free. ManualSearcher. com If you continue to use this site we will assume that you are happy with it. Read more Ok. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share. Note that email addresses and full names are not considered private information. Please mention this; Therefore, avoid filling in personal details. The manual is 1,44 mb in size. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive. Check your email Please enter your email address. For details on FINE Cartridge replacement, refer to “Replacing A FINE Cartridge” in this guide. 1 2 3. 87 Summary of content (87 pages) Page 1 User’s Guide Table of Contents Introduction Before Using Your Machine The following FINE Cartridges are compatible with this machine. For details on FINE Cartridge replacement, refer to “Replacing A FINE Cartridge” in this guide. All rights reserved. Trademarks Canon is a registered trademark of Canon Inc. All other product and brand names are trademarks of their respective owners. Page 3 Introduction Useful Information z Replacing a FINE Cartridge When the ink in the FINE Cartridge starts to run out, the machine will switch to memory reception of faxes.

See “Printing a Document in Memory” on page 35 See “Replacing a FINE Cartridge” on page 57 See “Aligning the FINE Cartridge” on page 60 z One-touch and Coded Dial Numbers You can register One-touch and Coded Dial numbers in your fax machine to make sending faxes easier and faster. Page 4 Reading the Documentation This guide provides detailed information on how to set up, operate, maintain, and troubleshoot your fax. Please read the list below to become familiar with the symbols, terms, and abbreviations used in this guide. Warning Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. In order to use the machine safely, always pay attention to these warnings. Page 5 Safety Precautions Please read the safety warnings and cautions provided in this manual to ensure that you use the machine safely. Do not attempt to use the machine in any way not described in this manual. If you use a cardiac pacemaker and feel abnormalities, please move away from this product and consult your doctor. Warning You may cause an electric shock, fire, or damage the machine if you ignore any of these safety precautions. Page 6 Choosing a location Do not install the machine in a location that is unstable or subject to excessive vibration. Do not install the machine in locations that are very humid or dusty, in direct sunlight, outdoors, or close to a heating source. Do not place the machine on a thick rug or carpet. Note z If an error message is displayed on the LCD, see “LCD Messages” on page 74. Page 10 Guidelines for Entering Numbers, Letters, and Symbols When you come to a step that requires you to enter a name or number, see the table below to determine which numeric button to press for the letter you want. Continue entering other letters or numbers using the numeric buttons. Setting the TEL LINE TYPE Before using your fax, make sure it is set for the telephone line type of your telephone system.

Thus, whenever you send a fax from this machine, the recipient receiving the fax knows who sent it, and when it was sent. You can enter a space to make your number easier to read. Page 16 Document Requirements. Types of Document You Can Scan z Scanned Area z Size The actual area scanned by the fax is shown below. You can load documents larger than 105 mm wide and 105 mm long. Page 17 Paper Requirements Your fax supports A4-, letter-, and legal-size paper in portrait orientation. You can use regular copier paper, cotton bond paper, or typical letterhead. Look at the label on the package to see if the paper has a preferred side for printing. Note Be sure to test paper before purchasing large quantities. Page 18 2 3 Squeeze, then slide the Paper Guide to the left. Insert the stack face up into the MultiPurpose Tray (1), and align the right edge of the stack with the right side of the MultiPurpose Tray. Then slide the Paper Guide (2) snugly against the left edge of the stack. Be careful not to press the Paper Guide strongly against the stack, or the paper will not be fed properly. Page 19 Copying Making Copies One of the convenient features of the fax is its ability to make high quality copies. You can make up to 99 copies of one document at a time. Page 20 Sending Faxes Sending Documents Before you send a document, see “Documents Requirements” on page 14, and “Loading Documents and Paper” on page 15. Note z If paper jams, see “Troubleshooting” on page 65.You cannot add pages while the fax is sending. Page 21 3 If a person answers, converse normally, then ask them to press the start button on their fax.Make sure the Handset is seated properly in its cradle. If you do not want the fax to beep, disable the setting (see page 49). Page 23 ? Sending a Document Using Directory Dialing This feature is convenient when you know the other party’s name but cannot recall the one-touch speed dialing button or the code for coded speed dialing where the number is registered.

This procedure can also be used to look up the other party’s name and retrieve the number for dialing. 1 Load the document face up into the Document Tray. See “Loading Documents and Paper” on page 15. You can set the scanning resolution and the contrast (see page 19). The fax begins calling the number. See “Jams in the Document Tray” on page 65. ? Automatic Redialing z What is Automatic Redialing. When you are sending a document and the receiving party’s line is busy, the fax waits the specified time and then dials the same number again. You can set the fax to redial several times if previous attempts fail because of a busy signal. Delayed Sending Your fax can send a document automatically at a preset time. Page 27 9 The fax will automatically dial at the programmed time. ? Sending Other Documents While the Fax is Set for Delayed Sending You can send, receive, and copy other documents even when the fax is set for sending at a preset time. To send or copy other documents after setting the fax for delayed sending, simply send or copy using any other sending procedure in this guide. Page 28 Sequential Broadcasting. Sending a Document to More Than One Location Sequential broadcasting sends one document to more than one location. Page 29 Receiving Faxes Different ways to receive a document Your fax provides you with several modes for receiving documents. To determine which mode best suits your requirements, see the table below. Receives documents automatically and rings for voice calls (see page 28).If you subscribe to this service, your line is assigned two numbers: one for fax and one for phone. When the fax number is called, the network sends a specific ringing tone which your fax recognizes and automatically handles as a fax call. If the phone number is called, a different ringing tone is sent out from the network so that the call is handled as a voice call. Page 33 Telecom FaxAbility (New Zealand only) Telecom N.Z. offers the FaxAbility capability.

If you subscribe to this service, your line is assigned two numbers: one for fax and one for phone. If the phone number is called, a different ringing tone is sent out from the network so that the call is handled as a voice call.Page 35 4 Dial the fax number of the fax machine you wish to poll. Use one of the dialing methods described. Your fax begins receiving the document. Note z is only available in some countries.Page 37 Documents Stored in Memory. Use the Handset on the fax to record your outgoing message. Only one outgoing message, no longer than 20 seconds, can be recorded. Note You cannot receive documents while you are recording a message or voice memo. Also, the Caller ID function (see page 33) may not work properly. The fax returns to standby mode. To record a new outgoing message, repeat steps 1 to 7. The old outgoing message will be automatically deleted when you record your new message. Setting TAM MODE Setting allows you to receive telephone messages (ICM) and fax transmissions while the fax is unattended. When you cancel, any new telephone messages will be played automatically. Note When the recording time is set to 0, the alternative outgoing message is played. If an alternative outgoing message has not been recorded, the outgoing message is played. Recording Voice Memos Use this feature when you are going out and want to leave a message for another member of the family. Use the Handset on the fax to record your voice memo. The old outgoing message will be automatically deleted when you record your new message. Page 44 Remote Control Features Use these features when you call home to play back any messages you may have received. You can also use the remote control features to set. Page 45 Note z A password is required to use the remote control features. However, if is set to (see page 52), it is not necessary to enter your password when you use the feature (see page 45).If you enter two invalid passwords consecutively, the call will be disconnected.

You can use remote control to access the forwarding number and listen to your telephone messages. Note z You must register a forwarding number and set before you can use this feature. Remote control cannot be used to set this feature unless a forwarding number has been registered. Page 49 Note z When forwarding is not possible: You can set the fax to redial the forwarding number a certain number of times at specified intervals when forwarding is not possible, such as at times when the forwarding number is busy or the phone is unattended. If forwarding is still not possible after the fax redials the forwarding number the specified number of times, the forwarding setting will be temporarily canceled. Page 50 Settings and Activity Reports Selecting a Menu The,,,,,,, and menus allow you to customize the way your fax works. REJECTION METHOD: Set the way the fax rejects calls. A maximum of 20 digits can be entered. Page 56 ? One-Touch Speed Dialing List Lists the numbers and names registered under one-touch speed dialing buttons. ? Coded Speed Dialing List Lists the numbers and names registered under coded speed dialing codes. ? User’s Data List Lists the current settings of the fax and the registered sender information. ? List of Documents in Memory Lists the documents currently stored in the fax’s memory (see page 35). When printing is finished, replace the FINE Cartridge immediately. The LCD displays. Page 59 ? Replacing a FINE Cartridge Note z Do not replace the FINE Cartridge while the fax is printing or performing another operation.Otherwise the Cartridge Holder may not be in its home position, causing the FINE Cartridge to remain uncapped and dry out. 1 2 Make sure the fax is turned on. Open the Printer Cover until it locks into place securely at the second bump. Page 60 5 Insert the new FINE Cartridge. (1) Insert the new FINE Cartridge slightly slanted. (2) Push up the FINE Cartridge until it clicks into place. 6 Close the Printer Cover.

(2) (1) Note Load the paper in the Multi-Purpose Tray before you replace the FINE Cartridge. Important z To maintain optimal print quality, we recommend that you use Canon brand FINE Cartridge. Replenishing ink only is also not recommended.Do not leave with the FINE Cartridge removed. The fax prints the nozzle check pattern. (1) Nozzle check pattern 4 If the pattern is broken or missing (1), clean the FINE Cartridge print head (see page 59). ? FINE Cartridge Cleaning If the pattern is broken or missing, clean the FINE Cartridge print head. Note Cleaning the print head consumes a small amount of ink. Note z After cleaning, print the nozzle check pattern to check if cleaning corrected the problem (see page 58).Aligning the FINE Cartridge If ruled lines are printed misaligned or print results are otherwise unsatisfactory, adjust the print head position. Page 63 (2) Repeat the procedure to input inputting the pattern number for columns B and C. Note If it is difficult to pick the best pattern, pick the setting that produces the least noticeable vertical white streaks. (A) (B) (A) Less noticeable white streaks (B) More noticeable white streaks (3) When you have finished inputting all pattern numbers, the fax returns to standby mode. Page 64 2 Use a clean, soft, dry, lint-free cloth to remove any ink or paper debris from the interior of the fax, especially around the four pinch rollers (A). (A) Dirt and dust particles that collect on the underside of the Printer Cover affect the quality of the documents you copy or send. Be careful not to touch the FINE Cartridge or its holder. 3 When you are finished, close the Printer Cover. Be sure to close the Printer Cover until it locks into place. Page 65 ? Cleaning The Roller Clean the paper feed roller if paper is not fed properly. Cleaning the paper feed roller will wear the roller, so perform this only when necessary. 1 2 3 4 5 6 Ensure that the machine is turned ON and there is no paper loaded in the MultiPurpose Tray.

Repeat steps 2 to 3 twice. Load three or more of A4- or Letter-sized paper in the Multi-Purpose Tray. Repeat steps 2 to 3 three times. Inspect the discharged paper. If dust or dirt can be seen on the paper, repeat the cleaning process. ? Cleaning The Protrusions Inside The Machine If protrusions inside the machine are stained, wipe ink off the protrusions using a swab or something similar. Caution Do not touch the transparent film (A), film cable (B), or any metal parts. Page 67 Troubleshooting Paper Jams. Jams in the Document Tray When a document jams or misfeeds in the Document Tray, and are displayed on the LCD.Page 68 2 3 4 Open the Printer Cover. Gently remove the jammed paper inside the fax. If the power disconnects, the following will apply: z You will not be able to send or receive faxes or make copies. Page 69 ? Multiple Sheets Load Into the Fax at the Same Time Cause Action Paper may not be loaded correctly. Make sure the paper stack is loaded properly in the Multi-Purpose Tray, and that the Paper Guide is adjusted correctly (see the Easy Setup Instructions). Sheets of paper may be sticking together. Be sure to fan the paper stack before loading it in the Multi-Purpose Tray. This keeps the sheets of paper from sticking together (see the Easy Setup Instructions). Page 70 Cause Action There may be other documents being sent from memory. Allow time for those documents to finish sending. An error may have occurred during sending. Print an activity report and check for an error (see page 53). The telephone line may not be working properly. If there is no dial tone, contact your local telephone company. The receiving fax machine may not be a G3 fax machine. Page 71 ? The Fax Does Not Switch Automatically Between Telephone and Fax Reception Cause Action The fax may not be set to switch automatically between telephone and fax reception. If you have set Page 72.

Fax Images Print Blotched or Uneven Cause Action The telephone lines may be in poor condition, or you may have a bad connection.The sending fax machine may not be functioning properly. The sending fax machine usually determines the quality of the document. Page 73 Telephone Problems. You Cannot Dial Cause Action The telephone line may not be connected properly. Make sure all line connections are secure (see the Easy Setup Instructions). The power cord may not be plugged in securely. Check that the power cord is plugged securely into the fax and into the wall outlet (see the Easy Setup Instructions). If the fax is plugged into a power strip, make sure the power strip is plugged in and turned on. The machine may not be switched on. Page 74 ? The Printout Contains Blurred or Smudged Ink Cause Action The paper you are using may not be supported by the fax. Make sure you are using the recommended paper (see page 15). You may be printing on the wrong side of the paper. Some papers have a “right” side for printing. If the print quality is not as clear as you would like it to be, try turning the paper over and printing on the other side. General Problems ? The Fax has no Power Cause Action The power cord may not be plugged in securely. Page 75 In Case of a Power Failure The user data settings and registered data for one-touch speed dialing and coded speed dialing are saved during a power failure. If however, the data cannot be retried when the power is tuned on again, a memory clear report is printed automatically. Page 76 LCD Messages The following messages are displayed on the LCD when the fax is performing a function or encounters an error. ? !!CHECK!! 5100 Cause Action Movement of the FINE Cartridge Holder is blocked. Clear the paper jam or foreign object that is preventing the FINE Cartridge Holder from moving, then turn off the machine and turn it back on again. There may be an obstruction that is not allowing the Cartridge Holder mechanism to move.

Check for any obstruction (paper clip, small object, etc. Page 77 ? CHECK DOCUMENT Cause The document is not set in the Document Tray, or has jammed. Action Set the document you are trying to send or copy (see page 15), or check for a document jam and clear the jam if necessary (see page 65), and start again. ? CHECK PAPER SIZE Cause The size of the paper in the multipurpose tray and that specified in the PAPER SIZE setting are different. Action Load the correct paper size or change the setting (see page 51). Action A FINE Cartridge that was once empty is installed. Replace the FINE Cartridge (see page 55). ? MEMORY FULL Cause Action The fax’s memory is full because it has received too many documents, or a very long or detailed document. Print and delete any documents stored in memory (see page 35). Action Listen to your telephone messages and delete any unnecessary messages. Page 81 Appendix For your safety (Australia only) To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities. The power point shall be located near the equipment and shall be easily accessible. Page 82 The automatic calling functions of this equipment must not be used to cause a nuisance to other Telecom customers. Under power fail conditions, this telephone may not operate, Please ensure that a separate telephone, not dependent on local power, is available for emergency use.http://www.gherlo.com/images/candy-washer-dryer-instruction-manual.pdf